Evinrude/Johnson/OMC 200 HP 1987 Model 200STLCU, 200TXCU

SELOC - Johnson/Evinrude Outboards, 1973-91 Repair Manual  #1308

• Covers all 60-235 HP, 3-Cylinder, V4 and V6, 2-Stroke Models, Includes Jet Drives
• 1973-1991
• Repair Manual

18-3059 Impeller

 18-3390 Water Pump Repair Kit Without Housing

 18-3392 Water Pump Repair Kit Without Housing

435526 Chrome Water Pump Kit

435990 Water Pump Impeller Housing

Note:  90/115 HP 1995-2006 Looper (except SL Model)

18-1506 Vernatherm

140 deg farenheigt

18-1117 Pinion Bearing

• Sierra Pinion Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1117
• Interchangeable with the following: Chrysler 31-F694057, 31-42647A1, GLM 21610, Evinrude/Johnson 387817, 5007751, Mallory 9-75121, Mercruiser/Mercury 31-42647A1, 31-42647
• Fit specific, check part numbers to ensure proper fit

18-1158 Marine Carrier Bearing

• Sierra Solenoid
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5815
• Interchangeable with the following: Arco SW275, GLM 72370, Mallory 9-15111, Mercury/Mercruiser 89-76545T, 89-61053, 89-68258, 89-68258A4, 89-76545, 89-15857
• Fit specific, check part numbers to ensure proper fit

18-1351 Carrier Needle Bearing

• Sierra Carrier Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1351
• Interchangeable with the following: GLM 22870, Evinrude/Johnson 382407, OMC 382407

18-1365 Thrust Bearing

• Sierra Thrust Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1365
• Interchangeable with the following: GLM 16330, Evinrude/Johnson 387656, 383248, OMC 387656
• Thrust Driveshaft Johnson/Evinrude 90-250hp OMC Stringer/Cobra All Models

18-1366 Thrust Bearing

• Sierra Thrust Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1366
• Interchangeable with the following: GLM 16300, Evinrude/Johnson 382408

18-2229 Driveshaft Shim

.003", 1.24 ID

18-2230 Driveshaft Shim

.004", 1.24" ID

18-2231 Driveshaft Shim

.005", 1.24" ID

18-3708 Prop Nut & Keeper

18-3715 Marine Prop Nut Kit

Kit Contents:

• 18-3708    398042    Prop Nut/Keeper
• 18-3741    309955    Cotter Pin
• 18-4231    320570    Prop Spacer

18-3741 Marine Cotter Pin

1/8" x 1 3/4"

18-4223 Marine Thrust Washer

18-4231 Marine Prop Spacer

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Other compatible propeller options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust), Right and Left Hand Rotation

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

OMC and Michigan Stainless Steel

Michigan Rapture Performance Stainless Steel

Michigan Ballistic High-Performance Stainless Steel

Other compatible prop options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Stainless Steel V6 135-300 HP & 90-130 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 177283 for Evinrude/Johnson V6 Outboards  Amazon  eBay
•  
• Note:  There is also a TBX Hub Kit that makes these propellers work with  Suzuki / Mercury / Honda / Yamaha  V6 outboards. 177288    Amazon   eBay
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru
• Note: All V6 stainless steel propellers, fitted to Evinrude® E-TEC® G2 outboards require an additional purchase of custom fit G2 TBX™ hub kit #767683   Amazon   eBay

Stainless Steel, Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

BRP Evinrude Polished Stainless Steel TBX Propellers

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation

BRP Evinrude Viper TBX Stainless Steel Propellers for Runabouts and General Recreation

If you want speed, you want the Viper prop.  It's longer swept blades and larger diameter give this prop a better grip on the water faster acceleration, and greater top-end speed.  Excellent on any recreational boat, from runabouts and cruisers to deck boats.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Versatile 3-Blade performance
• Excellent balance of speed and durability

BRP Evinrude Cyclone TBX Stainless Steel 4-Blade for Offshore Cruising and Runabouts

When you need a prop that can hold course straight and true in all water conditions, trust the Cyclone prop to maintain compass headings and stay hooked up in big water.  Designed for heavier and twin-engine boats as well as runabouts.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Ultimate performance 4-blade offshore and runabout propeller
• Stays on plane with minimum RPM
• Tracks true in all water conditions
• Less vibrations and improved fuel economy

BRP Evinrude Rebel TBX Stainless Steel 3-Blade Props for Offshore Cruising

The Rebel propeller is designed and engineered to deliver improved midrange cruising and top-end performance on V6 Evinrude E-TEC.  Large diameter and efficient blade contour provide faster speeds at lower RPMs to deliver significant improvement in fuel economy.  You will get more miles to the gallon and a longer cruising range.  Standard rotation and counter-rotation models are available from 15 to 25-inch pitch.  Use the Rebel propeller on offshore boats, large runabouts, and even large pontoon boats to make them perform to their maximum potential.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• High polish stainless steel
• Designed and engineered for efficient midrange cruising
• Improved fuel economy with a longer cruising range
• Use on offshore boats, large runabouts, and pontoon boats.

BRP Evinrude Raker H.O. Propellers for Bass Boats and High Performance

Looking to plane fast - and run faster?  The Raker II prop is specially designed for building up the engine RPMs and getting you on plane faster.  A great prop in surfacing conditions, especially when the boat is running over 50 mph.  Perfect for bass boats and high-performance boats.  The Raker propeller utilizes vent holes in the outer exhaust hub to allow exhaust gases to ventilate the blade area.  This allows the engine to build up RPMs and get the boat on plane faster.  At higher speeds, the water from rushing past the hub blocks these vent holes, preventing. them from ventilating the blades.  V6 Raker II use the TBX hub system

• Fast, Fast, Fast
• Uses the TBX hub system
• Custom cupped high rake blades provide superior bow lift and exceptional top-end speed
• Special vent holes for powerful acceleration
• Set the highest standards in top speed performance
• Maximizes the superior power and torque of Evinrude E-TEC G2 engine

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke, Aluminum Propellers

Evinrude/Johnson Aluminum Props

-More Performance for the Money!  Evinrude/Johnson props are cast with a custom aluminum alloy to give them greater strength and longer life than ordinary propellers.  Many of the Evinrude/Johnson outboards are speed cupped for better top-end performance.  Special baked-on corrosion-resistant paint gives added protection against saltwater and galvanic corrosion.

• Precision casting provides greater strength and longer life
• Baked-on corrosion-resistant paint gives added protection
• Engineered to match the power curve of your outboard for superior performance.

V6 Outboard 150-300 HP & 90 - 300 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 765195  Amazon  eBay for Evinrude/Johnson props with Interchangeable Hub 
• Other TBX Propeller Kits available competitive brands.
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru

V6 Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

18-5697 Starter Brush and Spring Set

• Sierra Brush and Spring Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5697
• Interchangeable with the following: Arco BK900, Chrysler F15164, 74384, Evinrude/Johnson 385952, Mercury 75384, 57390, 63292, 753841, 898265016, Mercury 75384

Power Trim Relay 586224 582472 584416 18-5705 Johnson Evinrude OMC

18-5808 STARTER SOLENOID

18-5832 Regulator/Rectifie

• Regulator/Rectifier for Johnson/Evinrude Outboard Engines
• Replaces: Johnson/Evinrude 583689, 583266, 586000, 584424 and CDI 193-3689
• For: Johnson/Evinrude Outboard Applications
• Sierra Part Number 18-5832
• All Sierra parts qualify for and are covered under Sierra's Industry Leading Customer Satisfaction Warranty

18-7094 Carburetor Needle and Seat

18-7248 Carb Kit

Note: 130 HP - P suffix only

398172 Powerhead Gasket Set

V6 Loop 90 deg

18-2075 Marine Oil Seal

Size: 1.562, OD: 2.062, Width: 0.300

18-2595 GASKET SET,SHIFT ROD & WEAR PLTE

18-2964 Head Gasket

18-3838 Head Gasket

 Champion (5828) Stainless Steel Marine Plug Spark Plug

• Unique anti-fouling design
• Engineered to exceed OE designs
• Maximum durability
• Designed for easy starting

18-5179 Ignition Plug In Coil

18-5891 Power Pack for 3 and 6 cylinder 6700 rpm limit.

• Sierra Power Pack
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5891
• Interchangeable with the following: CDI 113-3605, 583605, 763800, 583030, Mallory 9-25022

Champion 828M Spark Plug Ql77JC4

Also see:  Champion (5828) Stainless Steel Marine Plug Spark Plug

Also Fits Mercury Outboard

• 280 HP 2002 Offshore  2.5L EFI
• 280 HP 2002 Sport, SS 2.5L EFI
• 18 HP 1985-1980
• 9.8 HP 1985-1979
• 7.5 HP 1985-1979

Champion L77JC4 (821M) Copper Plus Small Engine Spark Plug

• .030 Gap

See Also:  Champion (5828) Stainless Steel Marine Plug Spark Plug

Sierra 18-1353 Center Main Bearing

• Sierra Center Main Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1353
• Interchangeable with the following: GLM 22810, Evinrude/Johnson 5007190, 387041

18-1377 Center Main Bearing

• Sierra Center Main Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1377
• Interchangeable with the following: GLM 22710, Evinrude/Johnson 352960, 320499

18-1389 Powerhead Bearing Kit

• The Sierra 18-1389 Powerhead Bearing Kit contains the following: (2) 18-1353 Center Main Bearing, (2) 18-1377 Center Main Bearing, (6) 18-1376 Wrist Pin Bearing, (1) 18-1396 Lower Crankshaft Bearing, (6) 18-1360 Rod Bearing. Each Sierra product meets or exceeds the original equipment part it replaces.
• Contains: (2) 18-1353 Center Main Bearing, (2) 18-1377 Center Main Bearing, (6) 18-1376 Wrist Pin Bearing, (1) 18-1396 Lower Crankshaft Bearing, (6) 18-1360 Rod Bearing

18-1396 Marine Lower Crankshaft Bearing

18-3904 Marine Piston Ring

3.500 inch Standard Bore

18-3905 Marine Piston Ring

• 4 and 6 cylinder
• 3.53 inch bore (.03 oversize)
• OMC 396504

18-4101 Marine Piston (Starbord) for Johnson/Evinrude

• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.500 + .030
• 2.530 inch (starbord) (.030 oversize)

18-4102 Piston Kit - .030 Port

• Loopcharged Pistons for 90 Degrees V4/V6/V8
• 2.530 inch (port) (.030 oversize)

18-4121 PISTON KIT - STBD

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.500 inch bore (starbord) (standard bore)
• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.500"

392591 Connecting Rod

• Johnson Evinrude Connecting Rod
• 392591
• C# 321712

Sierra 18-1360 Rod Bearing

• Sierra Rod Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1360
• Interchangeable with the following: GLM 22850, Evinrude/Johnson 396041, Mallory 9-51104

Sierra 18-1376 Wrist Pin Bearing

• Sierra Wrist Pin Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1376
• Interchangeable with the following: GLM 16230, Evinrude/Johnson 434844

18-4076 Rod Bolt

Sierra 18-4122 Piston Kit Standard Bore Port

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.500 inch bore (port) (standard bore)
• Loopcharged Pistons for 90 Degrees

18-3906 Marine Piston Ring

• 3.53 inch (.03 oversize)

Sierra International 18-4111 Marine Piston

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.520 inch bore (starbord) (.020 oversize bore)
• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.500 + .020

Sierra International 18-4112 Marine Piston

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.520 inch bore (port) (.020 oversize bore)
• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.520"

174003 Johnson Evinrude OMC OEM O-Ring Packagefor TNT

1982-1988 60-235HP 3 and 4 Cylinder with Prestolite Tilt Cylinder

18-7111 O-Ring

ID: 0.197, Width 0.113

18-7115 O-Ring

ID: 0.1735, Wisth: 0.135

18-7120 O-Ring

ID: 0.215, Width: 0.065

18-2002 Oil Seal

Size: 1.188, OD: 1.692, Width: .250

18-2061 Marine Oil Seal

Size: 0.822, OD: 1.375, Width: 0.195

18-2062 Marine Oil Seal

Size: 0.875, OD: 1.375, Width: 0.207

18-2074 Oil Seal

Size: 1.625, OD: 2.125, Width: 0.250

18-5619 Starter

90 deg V6 V8 Loop, Standard Rotation

115-300 E-TEC