OMC Evinrude/Johnson "SEA DRIVE" 1.8L 1987 Model Number 18AHPH

18-2219 Reverse Gear

18-2220 Sliding Clutch

18-2221 Gear Set

• Sierra Gear Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-2221
• Interchangeable with the following: GLM 22630, Mallory 9-73560
• Fit specific, check part numbers to ensure proper fit

Gear Set Contents:

• Part #        Desc.            O.E.#
• 18-2218  Forward Gear   434063
• 18-2219  Reverse Gear   333077
• 18-2220  Sliding Clutch   323664

18-2252 Prop Shaft

• Sierra Prop Shaft
• Meets or exceeds the original equipment quality
• Sierra part number: 18-2252
• Interchangeable with the following: GLM 22416, Evinrude/Johnson 436888, 387818, OMC 387818
• Fit specific, check part numbers to ensure proper fit

18-5832 Regulator/Rectifie

• Regulator/Rectifier for Johnson/Evinrude Outboard Engines
• Replaces: Johnson/Evinrude 583689, 583266, 586000, 584424 and CDI 193-3689
• For: Johnson/Evinrude Outboard Applications
• Sierra Part Number 18-5832
• All Sierra parts qualify for and are covered under Sierra's Industry Leading Customer Satisfaction Warranty

Sierra 18-6759 Tilt and Trim Motor (Motor Only)

• Newer two-wire design for most 2, 4, 6 and 8 cylinder engines, fits applications 1982 to present
• Connection Type: 3 Bolt
• Use 18-7510 O-Ring

DB Electrical TRM0004 Power Tilt Trim Motor For Evinrude, Johnson, OMC, Sea-Drive All Models 81-92 /391264, 393259, 393988, 394176, 983019 /PT301NM /18-6759 /6220

18-3837 Head Gasket

582262 Power Pack

18-3904 Marine Piston Ring

3.500 inch Standard Bore

18-4101 Marine Piston (Starbord) for Johnson/Evinrude

• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.500 + .030
• 2.530 inch (starbord) (.030 oversize)

18-4076 Rod Bolt

Sierra 18-4122 Piston Kit Standard Bore Port

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.500 inch bore (port) (standard bore)
• Loopcharged Pistons for 90 Degrees

Sierra International 18-4112 Marine Piston

• V4 and V6 Small Bore Loopers
• 120-300 HP
• 3.520 inch bore (port) (.020 oversize bore)
• Loopcharged Pistons for 90 Degrees V4/V6/V8 120HP (1985-1987) 140HP (1985-1987) 200HP (1986-1987) 225HP (1986-1987) 275HP (1985-1987) 300HP (1985-1987) Size: 3.520"

18-2623 Lower Unit Seal Kit

Note:  2004-AB E-TEC - Non SLE gearcase only

Complete Lower Unit Seal Kit for Johnson Evinrude V4, V6, V8

18-2623 is an equivalent to an earlier OEM number 439141 (this number is no longer available from the OEM, now 439141 supersedes to part number 5006373).

18-8384 is equivalent to 5006373 (neither of these is equivalent to the 18-2623)

The OEM part 18-8384 and 5006373 are used to replace all earlier part numbers including the 18-2623, while the 18-2623 and 439141 are limited models that call for this specific number or an earlier number that supersedes up to OEM number 439141.

Seal Kit Contents
Part #    Desc.          O.E. #       Qty.
18-0110 Shift Housing Gasket 314082 1
18-2001 Seal 330137 2
18-2002 Seal 320862 2
18-2026 Seal 321453 2
18-2061 Seal 329922 1
18-2062 Seal 329923 1
18-2377 Screw 316563 4
18-2378 Magnetic Drain Screw 318544 1
18-2536 O-Ring 315788 1
18-2557 Impeller Gasket 338484 1
18-4248 Washer 311598 2
18-7109 O-Ring 317178 1
18-7120 O-Ring 307853 1
18-7127 O-Ring 313446 1
18-7130 O-Ring 314728 1
18-7133 O-Ring 305123 2
18-7137 O-Ring 318372 2
18-7142 O-Ring 322119 1
18-7144 O-Ring 333572 3
18-7145 O-Ring 332584 1
18-7475 Washer 328743 4
18-8300 Seal 341280 1
18-8301 Seal 341281 1

Sierra Marine Lower Unit Seal Kit is equivalent to parts:

• 439141 Evinrude Johnson OMC BRP
• 9-74106 Mallory Marine

18-2218 Forward Gear Set

18-5619 Starter

90 deg V6 V8 Loop, Standard Rotation

115-300 E-TEC