Evinrude/Johnson/OMC/BRP 40 HP 1984 Commercial Model 40RCP 40RCL 40RCYP 40RWCR 40RWLC

Clymer - 1973-1990  EVINRUDE/JOHNSON OUTBOARD 2-40 HP SHOP SERVICE MANUAL B732

• Covers 2 - 40 HP 2-Stroke
• 1973-1990
• Outboard Shop Manual

SELOC - Johnson/Evinrude Outboards 1973-89 Repair Manual #1302

• Covers all 1.25-60 Hp, 1 and 2-cylinder, 2-stroke models.
• 1973-1989
• Repair Manual

18-3083 Sierra Impeller

18-3336 Water Pump Housing

18-3366 Sierra Impeller

 18-3379 Water Pump Repair Kit Without Housing

• The Sierra 18-3379 Water Pump Kit without Housing is interchangeable with the following: Evinrude/Johnson 0390381, 0391741. Contains the following: (1) 18-3332 Grommet, (1) 18-3352 Wear Plate, (2) 18-3354 Water Pump Gasket, (1) 18-3366 Impeller.
• Sierra Water Pump Kit without Housing
• Contains the following: (1) 18-3332 Grommet, (1) 18-3352 Wear Plate, (2) 18-3354 Water Pump Gasket, (1) 18-3366 Impeller
• Sierra part number: 18-3379
• Interchangeable with the following: Evinrude/Johnson 0390381, 0391741

390613 Water Pump Impeller Housing

18-2355 Marine Prop Shaft

For: 35, 40, 48, 50, 55, 60, 70, 75 HP 2 & 3 cyl outboards (1975-1987)

18-4230 Marine Thrust Washer

25 - 40 HP Aluminum Propellers for Evinrude Johnson (Pin Drive)

• For Evinrude Johnson OMC
• 25 HP 1951-1955
• 28 HP 1962-1964
• 30 HP 1956
• 33 HP 1965-1970
• 35 HP 1957-1959
• 40 HP 1960-1976
• 40 HP Commercial  1978-1985
• Right Hand Rotation
• Hard to find on Amazon, but they have them on eBay.

Sorted by Pitch. 

Pitch is how far, in inches,  the boat would travel with 1 prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

25 - 40 HP  Pin Drive Props for Evinrude Johnson

40 - 75 HP Aluminum Propellers for Small 3-3/8" Gearcase (Thru-Hub Exhaust), 13 Tooth Spline

For Evinrude Johnson OMC BRP, 13 Tooth Spline

• 40-75 HP (Small Gearcase & Thru-Hub Exhaust)
• 13 Tooth Spline, 3-3/8 inch gearcase
• Be sure to count the number of spline teeth on your prop shaft.
•  
• 40 HP, 2 Cyl, 1984 - 2005
• 48 HP, 1987-1996
• 50 HP, 2 Cyl, 1975 - 2005
• 55 HP, 2 Cyl, 1976-1979
• 60 HP 2 Cyl, 1980-1985
• 65 HP, 2 Cyl, 1980-1985
• 75 HP, 3 Cyl, 1975-1985
• Sprint/Formula E  1986-1992

Sorted by Pitch. 

Pitch is how far, in inches,  the boat would travel with 1 prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

OMC and Michigan Aluminum Propellers

Michigan Vortex Aluminum Props,  XHS Drop-In Hub

• C Series Propellers Using XHS 111 or XHSII 221 Drop-In Hub Kit
• 13 Tooth Spline, 3-3/8 inch Gearcase, Thru-Hub Exhaust

40 - 75 HP Evinrude Johnson BRP Aluminum Propellers for Small 3-3/8" Gearcase (Thru-Hub Exhaust)

40 - 75 HP Evinrude Johnson BRP Stainless Steel Propellers for Small 3-3/8" Gearcase (Thru-Hub Exhaust)

Return to Propellers:

40 - 75 HP Stainless Steel Propellers for Small 3-3/8" Small Gearcase (Thru-Hub Exhaust), 13 Tooth Spline

For Evinrude Johnson OMC BRP, 13 Tooth Spline

• 40-75 HP (Small Gearcase & Thru-Hub Exhaust)
• 13 Tooth Spline, 3-3/8 inch gearcase
• Be sure to count the number of spline teeth on your prop shaft.
•  
• 40 HP, 2 Cyl, 1984 - 2005
• 48 HP, 1987-1996
• 50 HP, 2 Cyl, 1975 - 2005
• 55 HP, 2 Cyl, 1976-1979
• 60 HP 2 Cyl, 1980-1985
• 65 HP, 2 Cyl, 1980-1985
• 75 HP, 3 Cyl, 1975-1985
• Sprint/Formula E  1986-1992

Sorted by Pitch. 

Pitch is how far, in inches,  the boat would travel with 1 prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

OMC and Michigan Stainless Steel

Michigan Ballistic High-Performance Stainless Steel,  XHS Drop-In Hub

• C Series Propellers Using XHS 111 or XHSII 221 Drop-In Hub Kit
• 13 Tooth Spline, 3-3/8 inch Gearcase, Thru-Hub Exhaust

Michigan Rapture Performance Stainless Steel

Rubber Hub

40 - 75 HP Evinrude Johnson BRP Aluminum Propellers for Small 3-3/8" Small Gearcase (Thru-Hub Exhaust)

40 - 75 HP Evinrude Johnson BRP Stainless Steel Propellers for Small 3-3/8" Small Gearcase (Thru-Hub Exhaust)

Return to Propellers:

18-5671 Starter Drive Assembly

• Sierra Starter Drive Assembly
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5671
• Interchangeable with the following: Arco DV390, Evinrude/Johnson 384781
• Fits Sierra 18-5627, 18-5630, 18-5648 and OEM 585059, 586280, 586281 Starters

18-5697 Starter Brush and Spring Set

• Sierra Brush and Spring Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5697
• Interchangeable with the following: Arco BK900, Chrysler F15164, 74384, Evinrude/Johnson 385952, Mercury 75384, 57390, 63292, 753841, 898265016, Mercury 75384

18-5808 STARTER SOLENOID

18-7042 Siearra Carb Kit

Note: 25, 35 HP 1995-Up Except 3 Cylinder Models

18-7093 Sierra Carburetor Needle and Seat

18-7222 Sierra Carb Kit With Float

18-7820 Fuel Pump Kit 

• Sierra Fuel Pump Kit
• Contains 18-0850 Fuel Pump Gasket, 18-2900 Cap to Fuel Pump Gasket
• Sierra part number: 18-7820
• Interchangeable with the following: GLM 40820, Evinrude/Johnson 393103, Mallory 9-37702

438556 Evinrude Johnson OMC BRP Replacement Fuel Pump 20-140 HP

It of often cheaper to replace the entire fuel pump than to buy a repair kit.

18-4318 Powerhead Gasket Set

• Sierra Powerhead Gasket Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-4318
• Interchangeable with the following: Evinrude/Johnson 439083, 390076

Gasket Set Contains:

• 18-0963 Intake Manifold GasketTwin     335633     1
• 18-0850 Fuel Pump Mtg. Gasket            303615      1
• 18-0118 Carburetor Gasket                  325092       2
• 18-0983 Carburetor to Airbox               321497       1
• 18-3802 Head Gasket               327795,335359      1
• 18-0941 Water Jacket Cover Gasket      315538       1
• 18-0157 Air Box Split Gasket                330698       1
• 18-0128 Powerhead Mounting Gasket 326468, 351018  1
• 18-0136 Powerhead Mounting Gasket    328283         1
• 18-1224 Exhaust Cover Gasket             315869        1
• 18-1218 Exhaust Cover Gasket             315868        1
• 18-0182 Seal                                       310058        1

Note 50 HP 1971-1975 use 315539 Head Gasket, plus

Note 55 HP 1976 use 320658 Head Gasket, plus

Note 55/60 HP 1980-1985 2-Cylinder

18-2001 Oil Seal

18-2957 Head Gasket

18-3802 Head Gasket

18-5176 Ignition Coil

Champion 835 Spark Plug Ul81 UL81C

• .030 Gap

Champion 876M Spark Plug QL16V

• Plug Gap 0.30

13-1872 Upper Main Bearing

CAGED BEARING KIT

• GLM Part Number: 22800; Sierra Part Number: 18-1352; Mercury Part Number: 31-67445; OMC Part Number: 378252
• Metal Cage 16 NEEDLES
• 1.375 Journal Size 40C (1974-Thru) 45-60HP 2-Cyl. (1971-Thru) 3-Cyl. (All) V4 (1962-1978)

18-1374 Wrist Pin Bearing

• Sierra Wrist Pin Rod
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1374
• Interchangeable with the following: GLM 16220, Evinrude/Johnson 395627, Mallory 9-51103, Wiseco W5217

18-1378 Rod Bearing Complete

Johnson/Evinrude Rod Bearing for (18-135HP) Outboard

18-3914 .02 OS Marine Piston Rings

3.207/.020 Bore

18-4115 Piston Kit

• .020 Oversize

• Johnson Evinrude 2cyl

• Bore Size 3.207

18-4125 Marine Piston Kit

• Piston Kit Std Johnson/Evinrude 2 & 3 cyls 3.187 Bore
• Replaces: 391798,5006655 18-4125, 24110, 435546, 9-53400
• Standard Bore

Sierra 18-3913 Piston Ring

• For Evinrude/Johnson 2/3 Cylinder, 35-60 HP Motors
• Sierra Piston Rings
• Bore Size: 3.187/Std
• Sierra part number: 18-3913
• Interchangeable with the following: GLM 24310, Evinrude/Johnson 391170, 434107, Mallory 9-54400, Wiseco 3187KD

Sierra 18-3915 Piston Rings 3.217/.030

• Sierra Piston Rings
• For Johnson/Evinrude 3/2 Cylinder, 35-60 HP Motors
• Bore 3.217/.030
• Meets or exceeds the original equipment quality
• Sierra part number: 18-3915
• Interchangeable with the following: GLM 24330, Evinrude/Johnson 391416, 434109, Mallory 9-54402, Wiseco 3217KD

18-4324 Powerhead Gasket Set

18-7111 O-Ring

ID: 0.197, Width 0.113

18-7120 O-Ring

ID: 0.215, Width: 0.065

18-7123 O-Ring

ID: 2.235, Width: 0.100

18-7128 O-Ring

ID: 1.835, Width: 0.100

18-0543 Oil Seal

• OD: 1.926", Shaft: 1.540", Width: 0.243"

18-2021 Marine Oil Seal for OMC

Note:  40 HP 1988 - AR, AE, AT Models Only

Size: 0.750, OD: 1.375, Width: 0.250

18-2029 Marine Oil Seal for OMC

Size: 0.687, OD: 1.250, Width: 0.250

18-5630 Starter

375836 Recoil Starter Rewind Spring