Evinrude/Johnson/OMC/BRP 140 HP 2004 Model BJ140CX4RS BJ140L4SRS BJ140X4SRS J140CX4SRC J140PL4SRC J140PX4SRC

SELOC - Johnson Evinrude 40 - 250 HP, 2-Stroke Fuel Injected Models  #1313

• 40 - 250 HP, 2-Stroke Fuel Injected Models
• 2000-2006
• Repair Manual

SELOC - Seloc Johnson/Outboards 2002-07 Repair Manual: All 2-Stroke and 4-Stroke Models  #1314

• Covers 2.5 - 250 HP,  All 2 and 4-Stroke Models
• 2002-2007
• Repair Manual

18-3059 Impeller

18-3211 Marine Impeller Repair Kit

18-3346 Cup and Plate Assembly

 18-3390 Water Pump Repair Kit Without Housing

18-3391 Water Pump Housing Kit - With Housing

• Sierra Water Pump Kit with Housing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-3391
• Interchangeable with the following: GLM 12103, Evinrude/Johnson 395072
• Contains: 18-2557 Impeller Gasket, 18-2704 Grommet, 18-2769 Rubber Seal, (4) 18-3136 Bolt, 18-3153 Bolt, 18-3299 Impeller Key, 18-3346 Cup and Plate Assembly

90 - 140 HP (4-Stroke) Aluminum and Stainless Steel Propellers, (15 Spline) and Thru-Hub Exhaust

Fits the following Evinrude Johnson Outboards

• 15 Spline
• Standard RH Rotation
• Counter LH Rotation
• 90-140 HP 4-Stroke 2002 - Newer

BRP Evinrude Johnson Polished Stainless Steel

• 15 Spline
• Rubber Hub
• Standard RH Rotation
• Counter LH Rotation

Polished Stainless Steel

Since stainless steel is five times stronger than aluminum, the Stainless Steel Prop (SSP) can be designed and cast with thinner blades..blades that are cupped to provide better performance.

This versatile prop is an ideal upgrade replacement for aluminum propellers and provides greater performance for water skiing.

• Fast 3-blade versatile prop
• Ideal upgrade from aluminum
• Cupped blades provide superior performance

BRP Evinrude Johnson Aluminum

• 15 Spline
• Standard RH Rotation
• Rubber Hub

More performance for the Money!  Evinrude/Johnson props are cast with a custom alloy to give them greater strength and longer life than ordinary propellers.  Many of the Evinrude/Johnson outboards are speed cupped for better top-end performance.  Special baked-on corrosion-resistant paint gives added protection against saltwater and galvanic corrosion.

• Precision casting provides greater strength and longer life
• Baked-on corrosion-resistant paint gives added protection
• Engineered to match the power curve of your outboard for superior performance

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Stainless Steel V6 135-300 HP & 90-130 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 177283 for Evinrude/Johnson V6 Outboards  Amazon  eBay
•  
• Note:  There is also a TBX Hub Kit that makes these propellers work with  Suzuki / Mercury / Honda / Yamaha  V6 outboards. 177288    Amazon   eBay
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru
• Note: All V6 stainless steel propellers, fitted to Evinrude® E-TEC® G2 outboards require an additional purchase of custom fit G2 TBX™ hub kit #767683   Amazon   eBay

Stainless Steel, Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

BRP Evinrude Polished Stainless Steel TBX Propellers

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation

BRP Evinrude Viper TBX Stainless Steel Propellers for Runabouts and General Recreation

If you want speed, you want the Viper prop.  It's longer swept blades and larger diameter give this prop a better grip on the water faster acceleration, and greater top-end speed.  Excellent on any recreational boat, from runabouts and cruisers to deck boats.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Versatile 3-Blade performance
• Excellent balance of speed and durability

BRP Evinrude Cyclone TBX Stainless Steel 4-Blade for Offshore Cruising and Runabouts

When you need a prop that can hold course straight and true in all water conditions, trust the Cyclone prop to maintain compass headings and stay hooked up in big water.  Designed for heavier and twin-engine boats as well as runabouts.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Ultimate performance 4-blade offshore and runabout propeller
• Stays on plane with minimum RPM
• Tracks true in all water conditions
• Less vibrations and improved fuel economy

BRP Evinrude Rebel TBX Stainless Steel 3-Blade Props for Offshore Cruising

The Rebel propeller is designed and engineered to deliver improved midrange cruising and top-end performance on V6 Evinrude E-TEC.  Large diameter and efficient blade contour provide faster speeds at lower RPMs to deliver significant improvement in fuel economy.  You will get more miles to the gallon and a longer cruising range.  Standard rotation and counter-rotation models are available from 15 to 25-inch pitch.  Use the Rebel propeller on offshore boats, large runabouts, and even large pontoon boats to make them perform to their maximum potential.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• High polish stainless steel
• Designed and engineered for efficient midrange cruising
• Improved fuel economy with a longer cruising range
• Use on offshore boats, large runabouts, and pontoon boats.

BRP Evinrude Raker H.O. Propellers for Bass Boats and High Performance

Looking to plane fast - and run faster?  The Raker II prop is specially designed for building up the engine RPMs and getting you on plane faster.  A great prop in surfacing conditions, especially when the boat is running over 50 mph.  Perfect for bass boats and high-performance boats.  The Raker propeller utilizes vent holes in the outer exhaust hub to allow exhaust gases to ventilate the blade area.  This allows the engine to build up RPMs and get the boat on plane faster.  At higher speeds, the water from rushing past the hub blocks these vent holes, preventing. them from ventilating the blades.  V6 Raker II use the TBX hub system

• Fast, Fast, Fast
• Uses the TBX hub system
• Custom cupped high rake blades provide superior bow lift and exceptional top-end speed
• Special vent holes for powerful acceleration
• Set the highest standards in top speed performance
• Maximizes the superior power and torque of Evinrude E-TEC G2 engine

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke, Aluminum Propellers

Evinrude/Johnson Aluminum Props

-More Performance for the Money!  Evinrude/Johnson props are cast with a custom aluminum alloy to give them greater strength and longer life than ordinary propellers.  Many of the Evinrude/Johnson outboards are speed cupped for better top-end performance.  Special baked-on corrosion-resistant paint gives added protection against saltwater and galvanic corrosion.

• Precision casting provides greater strength and longer life
• Baked-on corrosion-resistant paint gives added protection
• Engineered to match the power curve of your outboard for superior performance.

V6 Outboard 150-300 HP & 90 - 300 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 765195  Amazon  eBay for Evinrude/Johnson props with Interchangeable Hub 
• Other TBX Propeller Kits available competitive brands.
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru

V6 Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

18-6281 Tilt/Trim Motor

Heavy Duty

332820 Head Gasket

OEM Evinrude Johnson BRP Outboard Head Gasket (Low Octane) - 332820

5034644 Head Gasket

4-Stroke

Champion RC9YC (344) Spark Plug

Evinrude/Johnson

• 90 HP 2004-2003  DOHC 4-Cylinder 4-Stroke
• 115 HP 2004-2003  DOHC 4-Cylinder 4-Stroke
• 140 HP 2004-2003  DOHC 4-Cylinder 4-Stroke

18-2623 Lower Unit Seal Kit

Note:  2004-AB E-TEC - Non SLE gearcase only

Complete Lower Unit Seal Kit for Johnson Evinrude V4, V6, V8

18-2623 is an equivalent to an earlier OEM number 439141 (this number is no longer available from the OEM, now 439141 supersedes to part number 5006373).

18-8384 is equivalent to 5006373 (neither of these is equivalent to the 18-2623)

The OEM part 18-8384 and 5006373 are used to replace all earlier part numbers including the 18-2623, while the 18-2623 and 439141 are limited models that call for this specific number or an earlier number that supersedes up to OEM number 439141.

Seal Kit Contents
Part #    Desc.          O.E. #       Qty.
18-0110 Shift Housing Gasket 314082 1
18-2001 Seal 330137 2
18-2002 Seal 320862 2
18-2026 Seal 321453 2
18-2061 Seal 329922 1
18-2062 Seal 329923 1
18-2377 Screw 316563 4
18-2378 Magnetic Drain Screw 318544 1
18-2536 O-Ring 315788 1
18-2557 Impeller Gasket 338484 1
18-4248 Washer 311598 2
18-7109 O-Ring 317178 1
18-7120 O-Ring 307853 1
18-7127 O-Ring 313446 1
18-7130 O-Ring 314728 1
18-7133 O-Ring 305123 2
18-7137 O-Ring 318372 2
18-7142 O-Ring 322119 1
18-7144 O-Ring 333572 3
18-7145 O-Ring 332584 1
18-7475 Washer 328743 4
18-8300 Seal 341280 1
18-8301 Seal 341281 1

Sierra Marine Lower Unit Seal Kit is equivalent to parts:

• 439141 Evinrude Johnson OMC BRP
• 9-74106 Mallory Marine

434519 Johnson Evinrude OMC Trim & Tilt O-Ring & Seal Rebuild Kit

60-300 HP 1991-2006 TNT Units

18-7897 Oil Filter

• Sierra Oil Filter
• Meets or exceeds the original equipment quality
• Sierra part number: 18-7897
• Interchangeable with the following: Evinrude/Johnson 5033919, 778887, Mallory 9-57815, Suzuki 16510-82703
• Thread Spec: 3/4" x 16 or 19.1mm x 406.4mm NPT
• 140 HP EFI (2003-2005)