Evinrude/Johnson/OMC 150 HP 1996 Model 150CXED, 150ELED, 150EXED, 150GLED, 150ILED, 150JLED, 150NXED, 150SLED, 150EXED, 150WCLD, L150GLED

Clymer - Evinrude/Johnson 85-300 HP Two-Stroke 1995-2002  B737

• Covers 85-300 HP, 2-Stroke
• 1995-2002
• Shop Manual

SELOC - Johnson Evinrude 1992-1996 4-6-8 Cylinder Repair Service Manual  #1310

• Covers 80 - 300 HP 2-Stroke
• 1992-1996 Repair Manual

SELOC - Johnson/Evinrude Outboards, All V Engines, 1992-01 1st Edition  #1311

• Covers all 65-300 Hp, V4, V6 and V8 engines
• 1992-2001
• Repair Manual

18-3059 Impeller

18-3211 Marine Impeller Repair Kit

18-3315-2 Water Pump Kit With Housing

• For 90/115 SL (1995-up)
• 120/125ESX (1993-1994)
• 120/130/140/150/175 V6 & V8 (1993-up)

18-3346 Cup and Plate Assembly

 18-3390 Water Pump Repair Kit Without Housing

18-3391 Water Pump Housing Kit - With Housing

• Sierra Water Pump Kit with Housing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-3391
• Interchangeable with the following: GLM 12103, Evinrude/Johnson 395072
• Contains: 18-2557 Impeller Gasket, 18-2704 Grommet, 18-2769 Rubber Seal, (4) 18-3136 Bolt, 18-3153 Bolt, 18-3299 Impeller Key, 18-3346 Cup and Plate Assembly

 18-3392 Water Pump Repair Kit Without Housing

435526 Chrome Water Pump Kit

435990 Water Pump Impeller Housing

Note:  90/115 HP 1995-2006 Looper (except SL Model)

18-2216 Sliding Clutch

• Sierra Sliding Clutch
• Meets or exceeds the original equipment quality
• Sierra part number: 18-2216
• Interchangeable with the following: GLM 22625, Evinrude/Johnson 337772, 37774, 334516, 336562, 910995, Mallory 9-72534, OMC 910995, 334516

18-2251 Prop Shaft

• Sierra Prop Shaft
• Meets or exceeds the original equipment quality
• Sierra part number: 18-2251
• Interchangeable with the following: GLM 22417, Evinrude/Johnson 5004765, 436740, 435022, 433017
• Fit specific, check part numbers to ensure proper fit

18-2327 Upper Drive Shaft Assembly

18-2330 UPPER DRIVE SHAFT (Extra Long)

18-3708 Prop Nut & Keeper

18-4223 Marine Thrust Washer

18-4231 Marine Prop Spacer

18-9219 Lower Drive Shaft

• Sierra Lower Drive Shaft
• Meets or exceeds the original equipment quality
• Sierra part number: 18-9219
• Interchangeable with the following: GLM 22407, Evinrude/Johnson 335677
• Lower Drive Shaft for Some Johnson Evinrude 90 to 225 HP Replaces 345905 335677

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Other compatible propeller options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust), Right and Left Hand Rotation

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

OMC and Michigan Stainless Steel

Michigan Rapture Performance Stainless Steel

Michigan Ballistic High-Performance Stainless Steel

Other compatible prop options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Stainless Steel V6 135-300 HP & 90-130 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 177283 for Evinrude/Johnson V6 Outboards  Amazon  eBay
•  
• Note:  There is also a TBX Hub Kit that makes these propellers work with  Suzuki / Mercury / Honda / Yamaha  V6 outboards. 177288    Amazon   eBay
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru
• Note: All V6 stainless steel propellers, fitted to Evinrude® E-TEC® G2 outboards require an additional purchase of custom fit G2 TBX™ hub kit #767683   Amazon   eBay

Stainless Steel, Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

BRP Evinrude Polished Stainless Steel TBX Propellers

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation

BRP Evinrude Viper TBX Stainless Steel Propellers for Runabouts and General Recreation

If you want speed, you want the Viper prop.  It's longer swept blades and larger diameter give this prop a better grip on the water faster acceleration, and greater top-end speed.  Excellent on any recreational boat, from runabouts and cruisers to deck boats.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Versatile 3-Blade performance
• Excellent balance of speed and durability

BRP Evinrude Cyclone TBX Stainless Steel 4-Blade for Offshore Cruising and Runabouts

When you need a prop that can hold course straight and true in all water conditions, trust the Cyclone prop to maintain compass headings and stay hooked up in big water.  Designed for heavier and twin-engine boats as well as runabouts.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Ultimate performance 4-blade offshore and runabout propeller
• Stays on plane with minimum RPM
• Tracks true in all water conditions
• Less vibrations and improved fuel economy

BRP Evinrude Rebel TBX Stainless Steel 3-Blade Props for Offshore Cruising

The Rebel propeller is designed and engineered to deliver improved midrange cruising and top-end performance on V6 Evinrude E-TEC.  Large diameter and efficient blade contour provide faster speeds at lower RPMs to deliver significant improvement in fuel economy.  You will get more miles to the gallon and a longer cruising range.  Standard rotation and counter-rotation models are available from 15 to 25-inch pitch.  Use the Rebel propeller on offshore boats, large runabouts, and even large pontoon boats to make them perform to their maximum potential.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• High polish stainless steel
• Designed and engineered for efficient midrange cruising
• Improved fuel economy with a longer cruising range
• Use on offshore boats, large runabouts, and pontoon boats.

BRP Evinrude Raker H.O. Propellers for Bass Boats and High Performance

Looking to plane fast - and run faster?  The Raker II prop is specially designed for building up the engine RPMs and getting you on plane faster.  A great prop in surfacing conditions, especially when the boat is running over 50 mph.  Perfect for bass boats and high-performance boats.  The Raker propeller utilizes vent holes in the outer exhaust hub to allow exhaust gases to ventilate the blade area.  This allows the engine to build up RPMs and get the boat on plane faster.  At higher speeds, the water from rushing past the hub blocks these vent holes, preventing. them from ventilating the blades.  V6 Raker II use the TBX hub system

• Fast, Fast, Fast
• Uses the TBX hub system
• Custom cupped high rake blades provide superior bow lift and exceptional top-end speed
• Special vent holes for powerful acceleration
• Set the highest standards in top speed performance
• Maximizes the superior power and torque of Evinrude E-TEC G2 engine

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

18-5697 Starter Brush and Spring Set

• Sierra Brush and Spring Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5697
• Interchangeable with the following: Arco BK900, Chrysler F15164, 74384, Evinrude/Johnson 385952, Mercury 75384, 57390, 63292, 753841, 898265016, Mercury 75384

Power Trim Relay 586224 582472 584416 18-5705 Johnson Evinrude OMC

18-5808 STARTER SOLENOID

18-5829 Regulator/Rectifier

• Sierra Regulator/Rectifier
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5829
• Interchangeable with the following: CDI 193-6048, Evinrude/Johnson 586048, Mallory 9-17204

18-5878 Stator

• 150-175 HP 1993-2006 Gray Sleve
• 35 Amp

18-6780 Tilt/Trim Motor

• Fit specific, check part numbers to ensure proper fit
• Evinrude Johnson Trim/ Tilt Motor 2 Wire 4 Bolt Mount
• 90/115 Crossflow (with Fastrack Midsection)
• V6 Commercial

18-7247 Carb Kit

• Sierra Carburetor Kit
• For V4 and V6, 1988-2001
• Sierra part number: 18-7247
• Interchangeable with the following: Evinrude/Johnson 438996, 436852, 435442, Mallory 9-37102

18-4406 Powerhead Gasket Set

150 60 degree (1991-2000), 175 60 degree (1991-2000)

• Powerhead gasket set
• Mallory 9-64107, Yamaha outboard 437155
• Backed by sierra's industry leading Warranty

V6 Loop 60 deg

18-5170 Ignition Coil

18-5794 Power PackCDI Electronics

UFI

This is for Quite rider series with longer wires due to power pack mounting location.

18-5887 Power Pack and Sensor

For V6 engines with an optical sensor and GRAY sleeve on the power pack.

Do not use with a BLACK sleeved stator.

Champion 938M Spark Plug QL78YC

Also see: CHAMPION MARINE SPARK PLUG 5939  Marine Stainless Steel

• Evinrude Johnson  0.030 Gap

Mercury Outboards

• 125 HP 2004-1994  4-Cylinder 
• 115 HP 2004-1989  4-Cylinder 2-Stroke
• 100 HP 1999-1988  4-Cylinder 
• 90 HP 2006-1987  3-Cylinder 2-Stroke
• 80 HP 1989-1978
• 80 HP 2004-1995  80 Jet 
• 75 HP 2006-1987  3-Cylinder 2-Stroke 2-Stroke
• 75 HP 1986-1984  4-Cylinder
• 75 HP 2001-1990  75 Sea Pro 2-Stroke
• 70 HP 1989-1987
• 65 HP 2004-1995  65 Jet 
• 60 HP 2002-1991  3-Cylinder 
• 60 HP 2004-1995  60 Big Foot 3-Cylinder 
• 60 HP 2004-1991  60 Sea Pro 3-Cylinder 
• 55 HP 2004-1992  55 Sea Pro
• 50 HP 2004-1991  50 3-Cylinder 2-Stroke 2-Stroke
• 45 HP 1989-1986
• 45 HP 2003-199  545 Jet 3-Cylinder 
• 40 HP 2004-1995  2-Cylinder
• 40 HP 2004-1997  3-Cylinder
• 40 HP 1997-1988  4-Cylinder
• 40 HP 2004-1995  40 Sea Pro
• 30 HP 2003-1995  2-Cylinder 2-Stroke 2-Stroke
• 30 HP 2001-1998  30 Jet 3-Cylinder
• 30 HP 1997-1995  30 Jet 3-Cylinder
• 30 HP 2004-1995  30 Sea Pro 2-Cylinde
• 25 HP 2004-1980  2-Cylinder 2-Stroke 2-Stroke
• 25 HP 2002-1993  25 Sea Pro 2-Cylinder
• 20 HP 1981-1970
• 20 HP 2003-1986  2-Cylinder 2-Stroke
• 20 HP 2004-1995  20 Jet 2-Cylinder
• 10 HP 1996-1991
• 10 HP 2004-1991  10 Sea Pro
• 10 HP 1998  XR10 
• 9.9 HP 1994-1986
• 9.8 HP 1978-1970 
• 7.5 HP 1978-1970
• 4.5 HP 1985-1975
• 4 HP 1987-1986
• 4 HP 1974-1973
• 4 HP 1972
• 4 HP 1971-1970

CHAMPION MARINE SPARK PLUG 5939  Marine Stainless Steel

• 0.30 Gap

Sierra 18-1353 Center Main Bearing

• Sierra Center Main Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1353
• Interchangeable with the following: GLM 22810, Evinrude/Johnson 5007190, 387041

18-4040 Marine Needle Bearing

5006714 Piston Kit  - .030 Oversize Port

5006716 Piston Kit - .030 Oversize Starboard

18-2290 Gear Set

18-3405 Water Pump Housing

434519 Johnson Evinrude OMC Trim & Tilt O-Ring & Seal Rebuild Kit

60-300 HP 1991-2006 TNT Units

5006688 Piston Kit -  Standard Starboard

5006708 Piston - .020 Oversize Port

5006715 Piston Kit  -  .020 Oversize Starboard

18-5612 Starter